You must have javascript enabled to use air-compressor.org !

【US】4.5KW BT30 Automatic Tool Changer ATC Spindle Motor Air

Cooled 24000RPM 220V

USD $1,745.00

Condition : New

Free Shipping

{{variant_type_name}} :
eBay
SKU: N/A This site contains affiliate links for which we may be compensated Business & Industrial / Industrial Automation & Motion Controls / Electric Motors / General Purpose Motors

Notify me when the price drops

We will email you if we find a lower price on this product!

Target price (USD) $

4.5KW BT30 ATC Air Cooled Spindle Automatic Tool Change 220V/380V+5.5KW Inverter 1 x 4.5KW Automatic Tool Changer Air Cooled ATC Spindle Motor 220V BT30 24000rpm 2 x Aviation plug 1 x BT30-ER25 Tool Holder with pull stud English user manual will send by email Note: We have 220V and 380V type for this model, pls leave us message when you order.   1 ) This spindle is built-in type spindle motor, built-in three asynchronous motors,by the inverter control.As the spindle has a compact structure,high power, big torque, small vibration, low noise characteristics,so it can achieve high speed,high powe cutting,high precision and high stability operation. 2 ) The bearing of spindle use grease lubricated angular to contact bearings,can be achieved lifelong lubricating within the life cycle. 3 ) The spindle use forced coolling mode to coolling motor,front and rear bearings.Coolant flow through the reasonable arrangement cycle watercourse of the spindle body,thus can take the heat generated of the spindle rotation speed, to achieve thermal equilibrium,let spindle temperature within a certain constant value. External cooling device effect:maintaining a constant temperature of the coolant. 4 ) The spindle built-in PTC 140 temperature sensor(Technical parameters are visible in other sections of this specification),you can read it anytime if you need to protect the motor temperature. 5 ) The tool clamping methods:this spindle built-in automatic tool change device,shank form is BT30. Please note that when stopping the spindle, you need to wait until the spindle is stopped before using the tool, so as to avoid causing the spindle and the tool mechanism to be connected together and cannot be separated. When loosening the tool and broaching the tool, you need to return the air, and pls keep the air intake and return air during the whole work. Product technical parameter table Spindle m odel : RTM1 2 0 x103-30 -24Z/ 4 .5 Voltage : 220 V or 380V Maximum speed : 24 000rpm Rated frequency : 8 00 Hz Electric current : 15 A Motor pole : 4Pole R ated power : 4.5 KW (S1) Peak power : 5.4 KW (S6) Rated torque : 3.5 Nm Peak torque : 4.2 Nm Product characteristic curve graph: Wiring  definition: Power supply, Fhermal, Fan Proximity switch and push button switch: Details: T echnical p arameters No. P roject Standard 1 Spindle blowing dust/seal gas pressure (MPa) 0.2-0.25 2 Spindle gas seal gas flow ( L/min) 65±10 ( When on Working ) 3 Cooling water pressure ( MPa) ≧ 0.25 4 Cooling water flow ( L/min) ≧ 2.5 5 Cooling water temperature( ℃ ) 24-28 6 Spindle static state pulse ( µm ) ≦ 3 7 Spindle vibration ( mm/s ) ≦ 1.0 8 Spindle assembly method Bottom mounting ( 6-M8 ) 9 Motor windings Pressure test ( V/M ) 1000 V/1 minute withstanding Voltage test 10 Tool Interface BT30 11 Inverter Specifications 5.5 KW (220 V or 380V) 12 Fitment Woodworking machinery, polishing industry, etc. 5. Spindle installation explanation 1) F an cooling system description When the spindle rotates, the rear fan system must be started to ensure the correct supply voltage and the supply voltage is 12V. 2) Air sealing control (AS) In order to prevent water or impurities enters internal of the spindle,spindle will have gas sealing device,t he gas seal machine must be started start with the machine at the same time. And the need to go through multi-stage filtration. 3) Compressed gas quality requirements The quality requirement of gas which is used in gas seals: Oil content : ﹤0.01mg/m³ S olid particle : ﹤5µ m Pressure dew point : ﹤7.5℃ ( 0.7MPa ) 4) Running-in program instructions Only all monitoring issued no failures operational signals,at the same time,all safety devices have been installed and working properly,then allow start spindle. Note: new or spindle which is not used for a long time must to be running slowly.First,start run spindle for half an hour as 25% of the maximum speed,then increase to 50% of the maximum speed,to run 15 minutes,finally, increase to maximum speed. It’s n eed to check the temperature of the spindle d uring the whole process, spindle will get hot, but not hot hand, if the spindle becomes hot, pls stop the operation and contact our customer service department. 5) Product backend interface instructions No. Function D efinition 1 Gas sealing ( Protection of impurities into the spindle 0.2-0.25MPa ) Ф 6 2 Return air ( piston reset 0.35-0.45MPa ) Ф 6 5 Power supply ( Spindle power lines with thermistor ) U/V/W/ Ground wire 6 Intake air ( Spindle loose knife 0.5-0.6MPa ) Ф 6 7 Sensor ( spindle tool change signals 24V ) Broach / loose knife 8 Fan ( spindle cooling ) 12V 6) PTC140 Temperature coefficient thermistor parameters Our products are equipped with a single thermistor PTC140, it can be used for spindle temperature protection . Parameter name Parameter symbol Single core Three core Series connection Unit Maximum DC working temperature Umax 30 30 V Rated control temperature Tk Designed according to user ℃ Rated control temperature tolerance T1 ±5 ℃ ±5 ℃ ℃ Rated control temperature tolerance T2 ±0.5 ℃ ±0.5 ℃ ℃ Resistance value on 25 ℃ R25 ≤ 100 ≤ 300 Ω Rated control temperature on -5 ℃ resistance value Tk-5 ℃ ≤ 550 ≤ 1600 Ω Rated control temperature on +5 ℃ resistance value Tk+5 ℃ ≥ 1330 ≥ 4000 Ω Rated control temperature on +15 ℃ resistance value Tk+15 ℃ ≥ 4 ≥ 12 KΩ Thermal response time Ta ≤ 5 ≤ 5 S Dielectric strength Uis AC2.5 AC2.5 KV Maximum control temperature Tkmax 180 180 ℃ Maximum allowable storage temperature Tmax 180 180 ℃ Minimum allowable storage temperature Tmin -40 -40 ℃ 7 ) Product Tool Change Signal s Description Sensor Model (0-24V, PNP), The spindle built two sensors.wiring Diagram is as follows: 1. Response broach knife signal, when the knife handle is hang, black sensor output signal; 2. Response loose knife signal, when the knife jaws open, black sensor output signal;

Returns Accepted for this item if it's within 30 Days

【US】4.5KW BT30 Automatic Tool Changer ATC Spindle Motor Air Cooled 24000RPM 220V
See more
Price type
IN STOCK OUT STOCK