You must have javascript enabled to use air-compressor.org !

(US Stock) 4.5KW ATC Automatic Tool Change Air Spindle Motor BT30

800HZ 220V CNC

USD $1,682.00

Condition : New

Free Shipping

{{variant_type_name}} :
eBay
SKU: N/A This site contains affiliate links for which we may be compensated Business & Industrial / Industrial Automation & Motion Controls / Electric Motors / General Purpose Motors

Notify me when the price drops

We will email you if we find a lower price on this product!

Target price (USD) $






【USA Stock】
(US Stock) 4.5KW ATC Automatic Tool Change Air Spindle Motor BT30 800HZ 220V CNCfor CNC Router Milling Engraving Machine


Good New:

We have USA Warehouse in United States,so we will ship this item from USA Warehouse to you.




Package included:

1 x 4.5KW ATC Automatic Tool Change Air Cooled Spindle Motor 220V ( 24000rpm,10.7A,800Hz, 4pcs bearing )

1 x BT30-ER25 Tool Holder with 45° pull stud

2 x Aviation plug

English user manual 


Notice: if you also need the inverter,pls contact us via ebay message.

 

                                          100% Brand New and High Quality!!!






  • This listing does not include the above VFD




  • 1) This spindle is built-in type spindle motor, built-in three asynchronous motors,by the inverter control.As the spindle has a compact structure,high power, big torque, small vibration, low noise characteristics,so it can achieve high speed,high powe cutting,high precision and high stability operation.

    2) The bearing of spindle use grease lubricated angular to contact bearings,can be achieved lifelong lubricating within the life cycle.

     3)The atc spindle uses air cooling to cool the motor and front and rear bearings. The wind is provided by the fan at the rear end, from the rear of the spindle through the inner and outer air slots directly to the front of the spindle, thereby taking away the heat generated by the high-speed rotation of the spindle, achieving thermal balance, and keeping the temperature of the electric spindle within a certain value.

    4) The spindle built-in PTC 140 temperature sensor(Technical parameters are visible in other sections of this specification),you can read it anytime if you need to protect the motor temperature.

    5) The tool clamping methods:this spindle built-in automatic tool change device,shank form is BT30.


    Please note that when stopping the spindle, you need to wait until the spindle is stopped before using the tool, so as to avoid causing the spindle and the tool mechanism to be connected together and cannot be separated. When loosening the tool and broaching the tool, you need to return the air, and pls keep the air intake and return air during the whole work.



  • ProducttEchnicalparameter table

    SpindlemODEL:

    RTM120X103-30-24Z/4.5220v

    Voltage:

    220V

    Maximum speed:

    24000rpm

    Max frequency:

    800HZ

    Electric current:

    15A

    Motor Pole:

    4 Pole

    RAted power:

    4.5KW(S1)

    Peak power:

    5.4KW(S6)

    Rated Torque:

    3.5NM

    Peak Torque:

    4.2NM


    4.5kw air-cooled automatic tool change spindle is a high-end woodworking company designed to develophigh-power electric spindle bearings imported fom Germany, high-precision bearings, high precision, long life.The electric spindle fan cooling with Road gas seal structure, automatic tool changer with bt30 tool holder, feastautomatic tool change and improve the efficiency of the automated processing.  Procuct Name4.5KW air-cooled ATC spindlePower4.5KWVoltage220VTorque3.5Nm (Torque peaked at 12000 rpm)Speed3000~24000rpm/minMax Frequency800HzCurrent10.7AColletBT30Pole number4Cooling Type air coolingBarometric pressure6 barFixed wayTwo side,screw fixedNumber of phases3Bearing2*7008 +2*7006Warranty3-year
     

     

    Product characteristic curve graph:

    Wiring definition

    Power Supply, Fhermal, Fan

    Proximity switch and push button switch


    Details:






    TEchnicalparameters

    No.

    PRoject

    Standard

    1

    SpindleblowingDust/seal gas pressure (MPa)

    0.2-0.25

    2

    Spindlegas seal gas flow

    (L/min)

    65 + 10 (When onWORKING)

    3

    Cooling water pressure (MPa)

    ≧0.25

    4

    Cooling water flow (L/min)

    ≧2.5

    5

    Cooling water temperature(℃)

    24-28

    6

    Spindlestatic state pulse(M)

    ≦3

    7

    Spindlevibration (Mm/s)

    ≦1.0

    8

    Spindleassembly method

    Bottom mounting(6-M8)

    9

    MotorwindingsPressure test (V/M)

    1000V/1 minute withstanding Voltage test

    10

    Tool Interface

    BT30

    11

    Inverter Specifications

    5.5KW(220V)

    12

    fitment

    Woodworking machinery, polishing industry, etc.

    Spindleinstallation explanation

    1) Fan cooling systemDescription

    When the spindle rotates, the rear fan system must be started TOensure the correct supply voltage and the supply voltage is 12v.

    2) Air Sealing control(AS)

    In order TOprevent water or impurities enters internal of the spindle,spindle will have gas SealingDevice,the gas seal machine must be started start with the machine at the same time. And the need TOgo throughmulti-stage filtration.

    3) Compressed gas quality requirements

    The quality requirement of gas whichis used in gas seals:

    Oil Content:﹤0.01mg/m³

    Solid particle:< 5 * m

    PressureDew point:< 7.5Degrees C(0.7mpa)

    4) Running-in program instructions

    Only all monitoring issued no failures operational signals,at the same time,all safetyDevices have been installed and working properly,then allow start spindle.

    Note: new or spindlewhichIs not used for a long time must TObe running slowly.First,start run spindle for half an hour as 25% of the maximum speed,then increase TO50% of the maximum speed,TOrun 15 minutes,finally, increase TOmaximum speed.It 's need TOcheck the temperature of the spindleDuring the wholeProcess,Spindle will get hot, but not hot hand, if the spindle becomes hot, pls stop the operation and contact our customer serviceDepartment.

    5) Productbackend interface instructions

    No.

    Function

    DEfinition

    1

    GAS Sealing(Protection of impurities inTOthe spindle0.2-0.25MPa)

    Ф6

    2

    Return air (piston reset 0.35-0.45MPa)

    Ф6

    5

    Power Supply (Spindlepower lines with thermistor)

    U/V/W/ Ground wire

    6

    Intake air (Spindleloose knife0.5-0.6MPa)

    Ф6

    7

    sensor(spindle tool change signals 24V)

    Broach / loose knife

    8

    Fan(spindle cooling)

    12v

    6) PTC140Temperature coefficient thermistor parameters

    Our products are equipped with a single thermistor PTC140, it can be used for spindle temperature protection.

    Parameter name

    Parameter symbol

    Single Core

    Three core Series connection

    Unit

    Maximum DC working temperature

    Umax

    30

    30

    V

    Rated control temperature

    TK

    Designed according TOuser

    ℃

    Rated control temperaturetolerance

    T1

    ±5℃

    ±5℃

    ℃

    Rated control temperaturetolerance

    T2

    ±0.5℃

    ±0.5℃

    ℃

    Resistance value on 25℃

    r25

    ≤100

    ≤300

    Ω

    Rated control temperature
    On -5℃resistance value

    TK-5℃

    ≤550

    ≤1600

    Ω

    Rated control temperature
    On +5℃resistance value

    TK+5℃

    ≥1330

    ≥4000

    Ω

    Rated control temperature
    On +15℃resistance value

    TK+15℃

    ≥4

    ≥12

    KO

    Thermal response time

    TA

    ≤5

    ≤5

    S

    Dielectric Strength

    Uis

    AC2.5

    AC2.5

    KV

    Maximum control temperature

    TKmax

    180

    180

    ℃

    Maximum allowable storage temperature

    tmax

    180

    180

    ℃

    Minimum allowable storage temperature

    Tmin

    -40

    -40

    ℃

    7) ProductTool ChangeSignalsdescription

    sensor MODEL(0-24V, PNP), The spindle built two sensors.wiring Diagram is as follows:

    1. Response broach knife signal, when theKnife handleIs hang,black sensor output signal;

    2. Response loose knife signal, when theKnife jawsOpen,black sensor output signal;



BT30-ER25 Tool Holder with 45° pull stud




About us:

Our company is an emerging professional Cross-Border Electronic company.We,as an honor and responsible seller online,always try our effort to offer best quality and service to our customers with our 100% sincerity.We guarantee every product is of high quality and durable utility compared to other factories becayse we choose the best-buys goods. Besides,our company has a powerful technical support and perfect after-sales service. 



Shipping:

All items will be sent out with tracking within 1-2 business day after the payment received,may be a delay on weekends;


Return&Refund:                                                                      

1.Any reason required for all refund.Item must be in it's original condition and no physical damage,buyer responsible for all shipping cost.

2.When you have the parcel,and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos,we will help you to solve any problems.


(US Stock) 4.5KW ATC Automatic Tool Change Air Spindle Motor BT30 800HZ 220V CNC
See more
Price type
IN STOCK OUT STOCK