New 12 / 24 Volt 150 Psi 3/4hp Air Ride Air Suspension Compressor

This listing is for 1 - BRAND NEW 12V or 24V Air Compressor used in a wide variety of applications.  These include Air Suspensions, Air slides, RV leveling systems, on demand air, air horns, Air Brakes, Pond Aeration - off grid septic and wasterwater Pumps, and many more!  These can replace the much more expensive Thomas and Gast brands - comparable to the TA-4101, TA-3101, 270025, 270024, and many more. Provided in this kit is our Very Own DIY Pond's oil less, 12 or 24 volt air compressor. This base kit is designed for the “Do It Yourselfer” who wants a performance air compressor to build a personalized air system for their vehicle.  We also can provide  pressure switches, air tanks, solenoid valves, relays, manifolds, airline and fittings to help complete your air system. Contact us for assistance if needed. ***NOTE -- BEFORE STARTING: These COMPRESSOR REQUIRE  the use of a unloader assembly kit, ** for use with an air tank.  NOT included.   It is recommended to have the compressor located as close to the supply as possible. Do not exceed 20 ft. -  Unloader valve to exhaust the air within the discharge line for easier compressor start-up.  -  Circuit breaker  to protect the electrical circuit at the positive battery terminal connection. -  Pressure switch controls min and max pressure of the air tank,110 psi ON 135 psi OFF. -  One way check valve  to prevent air from bleeding back through the compressor head. AIR COMPRESSOR MOUNTING REQUIREMENTS: - Must be secured to a firm and level surface and can be mounted in any position. - Must be mounted high enough on the vehicle to avoid being  submerged in water. - Must mount in a dry area, not exposed to rain or wheel spray. - Do not install under the hood near the engine, insufficient  cooling may result. - Must be in a well ventilated area for cooling. A cooling fan is  located in the end cap; do not obstruct the fans intake ports. - The compressor has two ports at the cylinder head. Do not  remove the pipe plug installed at our factory; only use the open ⅜" female NPT port for the air discharge line. - When installing the discharge line, it must slope downwards  to the air tank to prevent moisture from collecting in the line (which could freeze in cold weather rendering the compressor inoperative). Description 12V HP3/4HP Series Air Compressor is a heavy duty compressor with vertical pump head configuration. These Air Compressors have a 100 percent duty cycle. Features Copper wire wound permanent magnet motor Oil-less design Sealed bearings PTFE piston ring Cast aluminum cylinder head Hard anodized aluminum cylinder and aluminum sleeve Compressor Specifications 12V DC 100 percent at 100 PSI duty cycle 3/4 HP Vertical head configuration Size is 11.5 inch x 6 inch x 9.5 inch or 293 mm x 153 mm x 242 mm (LxWxH) Weight is 17.7 lbs Details Vertical Pump Head Finish Anodized Volts 12 Volt Warranty 2 Year The heavy duty 12 VDC (Volts of Direct Current) and 24 VDC air compressors are ideal for filling air tanks for both the on and off-road markets.

These 3/4 horsepower compressors have an oil-less design, sealed bearings, PTFE piston ring, copper wire wound permanent magnet motor and a cast cylinder with a hard anodized aluminum sleeve. Mountable in any orientation - So mounting configuration does NOT Matter - unless your space does.

100% Duty Cycle (1 Hour @ 100 PSI)

150 PSI Max Working Pressure, Draws 22.5 AMPs

3.1 SCFM

11.5″ x 6″ x 9.5″, 17.7 lbs

158°F Max / -40°F Min Ambient Temperature

Returns Accepted for this item if it's within 30 Days