12-24 Volt Air Ride, Air Horn Compressor

This listing is for 1 BRAND NEW aftermarket Replacement 12 Volt or 24 Volt compressor used in many Air Seat Susp ension, Air Doors, Air Horns, Air Brakes, Air Clutches, Fuel Systems, Air Seats, etc.  RV Seats, RV Slides, Tractor Seats, Big Rig Seats. These Replacement Air Ride compressors offer a light duty solution for smaller air requirements and are designed to fill no larger than a 1.0 gallon air tank. Multiple duty cycles, mounting, compressor finish, and intake options are available depending on model - just ask for others than this one if needed. New aftermarket replacement air compressor for many MSG95G, MSG95A, MSG95AL, MSG93 & MSG97AL air suspensions + Thomas 215ADC38/12, 215ADC38/24, 136AADC56/12, 135ADC56/24, Fits Agco Replacement Part. Fits Agco Models. Made to Replace C12V Pictures are for representation only.  Actual item may vary in shape, style, colors, etc. FEATURES – Check Valve – Installation Instructions – – – – – – – – SPECIFICATIONS – 12-Volt /24-Volt – Permanent Magnetic Motor – Duty Cycle: 10% @ 100 PSI – Max. Working Pressure: 130 PSI – Max. Air Tank Size: 1.0 Gallon – Max. 12V Amp Draw: 12 Amps – Max. 24V Amp Draw: 7 Amps – Ingress Protection Rating: IP54 – Dimensions: 5.6″L x 2.2″W x 4.4″H – Net Weight: 2.25 lbs. – – – – – * For 12V Only. 12V – 130 PSI / 1.53 CFM – (12V) 24V – 130 PSI / 1.27 CFM – (24V) Please Note: Use thread sealant for proper installation. Thread tape is not recommended. Properly sealed, recommended torque for 1/8” is 10 ~ 11 ft. lbs. Recommended torque for 1/4” and 3/8” is 16 ~ 18 ft. lbs.
PERFORMANCE DATA 12-VOLT COMPRESSOR PSI CFM A BAR LPM A 0 1.53 7 0 43.5 7 10 1.00 9 1.0 28.0 9 20 0.95 10 2.0 25.5 11 30 0.90 11 3.0 22.7 11 40 0.85 11 4.0 20.7 12 50 0.77 12 5.0 18.3 12 60 0.72 12 6.0 16.3 12 70 0.65 12 7.0 13.7 12 80 0.60 12 8.0 11.7 12 90 0.54 12 9.0 10.0 11 100 0.48 12 110 0.44 12 120 0.39 12 130 0.35 11 * Supply Voltage: 13.8 Volts 24-VOLT COMPRESSOR PSI CFM A BAR LPM A 0 1.27 4 0 36.0 4 10 1.09 5 1.0 28.5 5 20 1.03 5 2.0 26.5 5 30 0.96 5 3.0 24.7 6 40 0.90 6 4.0 21.7 6 50 0.83 6 5.0 19.7 7 60 0.76 6 6.0 17.0 7 70 0.70 6 7.0 14.3 7 80 0.63 7 8.0 11.7 7 90 0.56 7 9.0 8.7 6 100 0.51 7 110 0.42 7 120 0.35 7 130 0.31 6 * Supply Voltage: 28.0 Volts * Due to redundant restrictions added to apparatus, for flow rate testing, actual flow rate at 0 psi may vary. FILL RATES if used with a tank system 12-VOLT COMPRESSOR 0.5 GALLON TANK FILL RATE 0 to 105 PSI 50 sec. (± 05 sec.) 85 to 105 PSI 15 sec. (± 03 sec.) 0 to 120 PSI 1 min. 05 sec. (± 05 sec.) 90 to 120 PSI 21 sec. (± 03 sec.) 1.0 GALLON TANK FILL RATE 0 to 105 PSI 1 min. 40 sec. (± 10 sec.) 85 to 105 PSI 30 sec. (± 05 sec.) 0 to 120 PSI 2 min. 10 sec. (± 10 sec.) 90 to 120 PSI 45 sec. (± 05 sec.) 24-VOLT COMPRESSOR 0.5 GALLON TANK FILL RATE 0 to 105 PSI 50 sec. (± 05 sec.) 85 to 105 PSI 15 sec. (± 03 sec.) 0 to 120 PSI 1 min. 03 sec. (± 05 sec.) 90 to 120 PSI 20 sec. (± 03 sec.) 1.0 GALLON TANK FILL RATE 0 to 105 PSI 1 min. 40 sec. (± 10 sec.) 85 to 105 PSI 30 sec. (± 05 sec.) 0 to 120 PSI 2 min. 05 sec. (± 10 sec.) 90 to 120 PSI 45 sec. (± 05 sec.) Guidelines for Selecting Mounting Location:
The selection of proper mounting location for your air compressor will help ensure a long and
trouble free compressor service life. Please pay close attention to the following guidelines:
1. Select a FLAT, UPRIGHT AND SECURE location where the compressor can be mounted.
2. To maximize air compressor performance, locate compressor as CLOSE TO THE BATTERY
as possible so that length of positive lead wire required is at a minimum.
3. Choose mounting location that is as cool as possible and AWAY FROM HEAT SOURCES.
The cooler the ambient temperature the less chance the compressor will overheat.
4. This compressor is moisture & splash resistant, but NOT WATER PROOF. Do not mount
compressor in locations where the unit is likely to come in contact with water.
5. If it is necessary to mount the air compressor further away from the battery, such as inside your vehicle or in the bed of your pickup, use a minimum 12 AWG positive lead wire for
remote installation. (See wire gauge reference chart)
6. Do not mount compressor near areas where flammable liquids are stored. MOUNTING AND WIRING
1. Disconnect ground cable from vehicle’s battery.
2. Temporarily position the air compressor in the location where it will be mounted.
3. Route ground wire to the negative post of the battery or to an appropriate grounding point
and cut ground wire to length as needed.
4. Mount air compressor with the four sets of 13/64” (5 mm) bolts, nuts, washers, and locking washers provided. Use of thread sealant recommended.
5. IMPORTANT: Please note, your compressor may have a check valve. DO NOT remove
check valve from the unit.
6. Connect compressor’s positive lead wire to one of the leads of your pressure switch.
7. Make sure that your compressor setup is properly fused. For appropriate fuse size,
refer to amp draw of compressor in the specifications section of this manual.
Round up when choosing a fuse.
8. Always locate fuse as close as possible to power source.
9. Before connecting to power source, re-check to make sure that all connections
are properly connected.
10. Connect and test compressor system by running the compressor for a short time to build up pressure in your air tank.
11. Once air pressure reaches preset cut out pressure of your pressure switch, the compressor
will shut off. Inspect all air line connections for leaks with soap and water solution.
If a leak is detected, the air line may not be cut squarely or pushed all the way in.
Tighten connections if needed.

Returns Accepted for this item if it's within 30 Days